how to change battery in apple tv remote

Download Article

Download Article

Apple Television remotes are designed to be sleek and visually highly-seasoned. This tin can make finding the battery compartment hard to detect and confusing to open, especially since information technology lacks the traditional screw-on back that remotes had for many years. The mode you open up the compartment volition vary depending on whether you lot take a newer aluminum remote or i of the older white remotes. Either style, replacing the battery in your Apple TV remote is quick and easy!

1. 1

   Locate the battery compartment on the underside of the remote. If you turn your silverish aluminum Apple tree Tv remote over, you should see a circular battery door with a minor groove in the middle. This compartment should be easy to find, as it is the only feature on the otherwise-polish underside of the remote.^[1]

   • You lot'll detect the battery when you open up this door.

2. 2

   Place a coin in the groove and plow information technology counterclockwise. To open the door, find a coin, and gear up the edge of the coin in the groove. Then, twist counterclockwise until the door pops off. Yous don't need to press downward very difficult, equally the groove is designed to be opened this way.^[2]

   • You lot can use any coin, although it may be easier to hold a larger coin.
   • You may as well be able to apply another object, similar a central or a spoon. Just endeavour to avert scratching the metal finish of the remote.

   Advertising

3. three

   Remove the dead battery. The battery will just drib out of the remote if you turn it upside down or angle it slightly. Grab the battery in your palm as it drops, or else y'all may struggle to find information technology again.^[iii]

4. 4

   Insert a new CR2032 3V coin battery, with the positive side facing upwardly. The positive side has a small "plus" sign on information technology, in addition to other words and markings. The negative side typically has no markings on information technology. You lot can find ane of these circular batteries online or at any electronics shop, and many drug and department stores.^[four]

   • You can normally notice these batteries in bulk packs to save a few trips to the store.

5. 5

   Twist the door back onto the remote. Once you take replaced the battery, you lot volition immediately demand to screw the door back onto the compartment, or else the battery will fall correct out. Simply twist the round door back in, turning it clockwise until it feels secure.^[5]

   • Don't twist also tightly, or else you could end up struggling to remove the door the side by side time the bombardment gets depression.

   Advertizing

1. ane

   Wait for the battery compartment on the back end of the remote. On an older, white-colored Apple tree Telly remote, you will find the bombardment compartment on the opposite side of the remote from the black casing at the front. You will run across a modest, round hole on the right-side corner of this flat edge.^[6]

   • The battery compartment is not on the underside, only rather forms the entire backside of the remote.

2. 2

   Insert a paperclip into the release button hole. Any pocket-size object that will fit into the hole on the remote volition work, but a paperclip is an easy and readily available selection. Straighten out i side of the paperclip, and then press the metal stop into the hole on the remote until you experience the compartment click out of place.^[7]

   • Examples of other objects you could utilise are thumbtacks, sewing needles, metal toothpicks, or one tip of thin, sharp pair of tweezers.

3. 3

   Slide the bombardment tray out. After you have pressed on the release push button, the compartment volition popular out slightly, allowing y'all to pull the tray all the way out of the remote. The bombardment will be sitting loosely in the tray, which has a small grip on the end that fits inside the remote.^[8]

   • Make sure you open the bombardment compartment with the controls facing upwardly on top of the remote, or else the battery will autumn out when y'all open up it up.

4. iv

   Remove the dead battery. You tin can grab the battery with your fingers to remove it from the tray, or you can turn the tray over into your palm and so that the battery falls out. Whichever method you choose, set the battery aside then that it doesn't autumn to the flooring and become lost.^[9]

5. 5

   Set a new CR2032 battery into the circular tray, positive side up. Identify the new battery in the slot with the side with a "plus" sign facing upwards. This side may as well accept a number of other markings on it, while the negative side is usually blank.^[10]

6. half dozen

   Re-insert the bombardment tray. To finish the battery replacement, just slip the tray back into the slot it came from. Press on the back of the tray with the release hole on it until you lot hear a click. The tray will exist secured every bit presently as yous hear a click. The end of the tray should exist completely inserted into the remote, and experience flush with the edges.^[11]

   Advertisement

Ask a Question

200 characters left

Include your email accost to get a bulletin when this question is answered.

Submit

Advertisement

Cheers for submitting a tip for review!

About This Article

Thanks to all authors for creating a page that has been read 4,777 times.

Is this commodity up to engagement?

Source: https://www.wikihow.com/Replace-an-Apple-TV-Remote-Battery

Posted by: henrypeargen.blogspot.com

Share this post